|
Innovate Motorsports Catalog
This is just a small selection of data logging and engine monitoring components
we have available.
Questions on Parts not listed? E-Mail Us nightrider@nightrider.com
Nightrider Exclusive Parts Quick
Order
LM-2: Digital Air/Fuel Ratio Meter
|
The LM-2 combines an air/fuel ratio meter, a full-function
32-channel datalogger, and powerful software to deliver a complete tuning
workshop for less than the cost of one dyno day. Whether you have a
piggy-back fuel controller, race carb, aftermarket ECU, ODB-II tuning
software, or a flash/chip programmer, an LM-2 is the tool you need to dial
in maximum HP. The meter’s award-winning
digital signal processing technology provides data on exactly how rich or
lean an engine is running at any load. The LM-2’s self-calibrating
circuitry also compensates for changes in temperature, altitude, and
sensor condition.
- Patented “Direct Digital” Wideband Technology
- Wideband O2 Compatible with ALL fuel types
- Single or Dual Channel Version Available
- OBD-II Scan tool- read/clear DTCs and log up to 16 channels of CAN
OBD-II Data
- Log directly to SD card (included)
- Playback log data on screen and/or with powerful LogWorks
software (included)
- Large high-contrast graphics LCD
- Built-in RPM converter (direct frequency or with optional inductive
clamp)
- 4 fully-differential analog inputs
- 2 configurable linear analog outputs
- Positive lock connectors for all connections
- Innovate MTS serial IN and OUT
- USB connection to your PC
The LM-2 also features two fully programmable linear analog outputs to
connect to analog gauges, dyno computers, ECUs, piggyback controllers, and
other devices with analog inputs. Analog output 1 comes setup from the
factory ready for narrowband simulation; analog output 2 is configured as
0 volt = 7.35 AFR and 5 volts = 22.39 AFR. With the provided LM Programmer
software these analog outputs may also be configured by the user. |
The LM-2 is available in two different kit configurations:
JUST RELEASED! LM-2 "Basic"
Kit.
1) The new LM-2 "Basic" Kit (Single Wideband O2)
includes the LM-2 meter, Bosch wide-band oxygen sensor, 8 ft sensor cable,
cigarette-lighter power adapter, USB cable for PC connection, weld-in bung
and plug, LogWorks software CD, and quick-start guide. P/N: 3837,
MSRP $349
*Note: The LM-2 "Basic" Kit out of the box only
includes accessories to display your Air/Fuel Ratio either on the meter
and/or on your PC. To log RPM, or to Output the wideband signal to an
external device you'll need the LM-2 Analog IN/OUT Cable optional
accessory. For OBD-II features you'll need the LM-2 OBD-II Cable optional
accessory. To record internally to your LM-2 you'll need the SD Card
optional accessory. This unit also comes in a cardboard box, the black
hardcase is an optional accessory LM-2 Carrying Case*
2) The LM-2 Kit (Single Wideband O2) includes the LM-2 meter, Bosch
wide-band oxygen sensor, 8 ft sensor cable, cigarette-lighter power
adapter, analog in/out cable, ODB-II/CAN interface cable, SD memory card,
USB cable for PC connection, weld-in bung and plug, LogWorks software CD,
and quick-start guide. Carrying Case also included! P/N: 3806,
MSRP $479
3) The LM-2 Duo Kit (Dual Wideband O2) includes the LM-2 meter, (2) Bosch
wide-band oxygen sensors, (2) 8 ft sensor cables, cigarette-lighter power
adapter, analog in/out cable, ODB-II/CAN interface cable, SD memory card,
USB cable for PC connection, (2) weld-in bung and plug kits, LogWorks
software CD, and quick-start guide. Carrying Case also included! P/N:
3807, MSRP $669. |
Exhaust Clamp - P/N 3728
|
Patent-pending, Venturi-effect, tapped exhaust
clamp for obtaining accurate lambda measurements in non-cat autos or other
engines. |
Price $75.00 |
LC-1 Wideband Controller
|
The LC-1 Lambda cable is a complete wideband controller
built in to a sealed cable. It features the same award-winning
patented digital measurement principal found in the LM-1
& LM-2,
and includes digital input, output, and 2 user programmable analog
outputs. (View
Video)
The LC-1 is more accurate than conventional designs costing many times
as much, and its self-calibrating circuitry can compensate for changes in
temperature, altitude and sensor condition. The LC-1 is ideal for
applications such as Dynos, Data Acquisition, Standalone ECUs, piggyback
fuel controllers, OBD-II software or chip programmers, and gauges. With
the LC-1, you can add additional wideband channels to your LM-1, convert
an existing narrow-band gauge, or add wideband capabilities to your dyno.
You can even tune individual cylinders by using multiple LC-1 kits.
|
Key Features
- Only fully
digital wideband controller.
- Auto calibration capability to compensate for changes in
temperature, altitude, and sensor condition.
- Two user programmable analog outputs.
- Permanent install applications
- Cost effective individual cylinder tuning.
- Easy to upgrade.
- Includes LogWorks
software
|
|
The LC-1 is also a key component of Innovate Motorsports'
Modular Tuning System (MTS). Using the LC-1's serial ports you can
daisy-chain other Innovate devices such as the XD-16, AuxBox (LMA-3),
DL-32, TC-4, and SSI-4.
1) The basic LC-1 kit ($199) includes the LC-1, sensor, cd which
includes software and manuals, bung and plug, and a serial cable to
connect to the PC.
2) The Standalone Gauge Kit ($329) includes the LC-1, sensor, XD-16
digital gauge, cd which includes software and manuals, bung and plug, and
a serial cable to connect to the PC.
Installation and Setup
Installation of the LC-1 is relatively simple. Complete documentation
is supplied, and the support
pages, user forum,
videos,
application
notes and tuner
resources can also speed you on your way to effective tuning. Innovate
also has a great network of local dealers, tuners, race shops, and dyno
shops that can assist you in choosing, installing, and getting the most
out of your Innovate products.
|
| |
|
|
Innovate Motorsports Modular Tuning System (MTS) Components
All Innovate Motorsports products are scalable and modular. You can easily
add capabilities as your needs grow or change, enabling you to build the perfect
tuning system for your needs. The MTS is scalable with all components sharing a
common digital protocol. This allows you to create chains of components
specifically meeting your custom tuning needs.
Call for ordering information. Free Shipping on MTS component orders over $200.
|
MTS Modules
|
|
|
|
|
|
|
|
|
|
|
|
| Description |
Digital AFR Wideband meter
and Scan Tool
1-WBO2 Sensor |
Digital AFR Wideband meter
and Scan Tool
2-WBO2 Sensor |
|
Wide Band O2 sensor
controller |
Programmable Digital AFR
Gauge |
Data Logger and Sensor
Controller |
4 channel Simple Sensor
Interface |
4 channel Thermocouple
Interface |
Data Logger and Sensor
controller |
Open Tune ODB-II/Can
Tuning Interface |
Open Tune ODB-II/Can
Tuning Interface
WIFI enabled |
|
LogWorks Tuning Software (PC)
|
LM-2 (#3806)
$479
|
LM-2 (#3807)
$669
|
|
LC-1 (#3769)
$199
|
XD-16 (#3780)
$229
|
DL-32 (#3782)
$499
|
SSI-4 (#3783)
$129
|
TC-4 (#3784)
$129
|
LMA-3 (#3742)
$249
|
OT-1 (#3790)
$149
|
OT-2 (#3790)
$179
|
|
●
|
●
|
|
●
|
|
●
|
●
|
●
|
●
|
●
|
●
I-Phone App
|
|
PC Data Logging- Requires Laptop
/ Netbook / PC
|
●
|
●
|
|
●
|
|
●
|
●
|
●
|
●
|
●
|
●
|
|
Internal Data Logging
|
32-ch., 36+ hours (17 min./MB)
|
32-ch., 36+ hours (17 min./MB)
|
|
|
|
32-ch., 36+ hours (17 min./MB)
|
|
|
|
|
|
|
Wideband Air/Fuel Ratio (Lambda)
|
1
|
2
|
|
1
|
|
|
|
|
|
|
|
|
Analog Outputs
|
2
|
2
|
|
2
|
|
|
|
|
|
|
|
|
Replace NBO2 Sensor
|
●
|
●
|
|
●
|
|
|
|
|
|
|
|
|
Integrated Digital Display
|
●
|
●
|
|
|
●
|
|
|
|
|
|
|
|
52mm Round Gauge Display
|
|
|
|
|
●
|
|
|
|
|
|
|
|
Warning Light
|
|
|
|
|
●
|
|
|
|
|
|
|
|
Analog Inputs
|
4
|
4
|
|
|
|
5
|
4
|
|
5
|
|
|
|
5V output for Ext. Sensors
|
|
|
|
|
|
●
|
●
|
●
|
●
|
|
|
|
RPM
|
●
|
●
|
|
|
|
●
|
●
|
|
●
|
|
|
|
Duty Cycle
|
|
|
|
|
|
●
|
●
|
|
●
|
|
|
|
Freq/Speed
|
|
|
|
|
|
●
|
●
|
|
●
|
|
|
|
EGT / CHT Thermocouple
|
|
|
|
|
|
1
|
|
4
|
1
|
|
|
|
Dual-Axis Accelerometer
|
|
|
|
|
|
●
|
|
|
●
|
|
|
|
MAP Sensor
|
|
|
|
|
|
To 44 psi
|
|
|
To 44 psi
|
|
|
|
OBD-II / CAN
|
●
|
●
|
|
|
|
|
|
|
|
●
|
●
|
MTS Example: 17-channel Log-Chain example
The example chain consists of a LM-1/LMA-2, a LC-1, a LMA-3, a
DL-32’s and 2 XD-16’s. In this case the chain has 17 channels (6 from LM-1,
1 from LC-1 and 5 each from the LMA-3 and DL-32).
Devices attached to the LM-1’s 'Aux In' port count as being part of
the LM-1’s 6 channels. They don’t count extra. XD-16’s do not contribute
any channels, so you can add as many as needed.
| |
Quick Links
|
